IK Multimedia iRig Stream Pro and iRig Stream Solo reviewed

0

IK Multimedia’s first iRig Stream was a huge success not only because it was right in the middle of the pandemic, but because it dramatically simplified the live streaming process. IK released two new models to meet creator demand, the iRig Stream Pro and the iRig Stream Solo.

iRig Stream Pro ($ 199)

The iRig Steam Pro is an enhanced edition of the original iRig Stream and provides everything you need for professional streaming in one interface. Simply put, it’s a 24-bit, 96kHz audio interface that works with iOS, Android, and Mac / PC devices.

You get an XLR / TRS combo input with a mic preamp so you can use it with a high-quality mic or TRS devices like a guitar or synth, etc. There is also an RCA, TRRS and device stereo input for the loopback function. With the Pro you also get a lot more control than in the previous edition, including volume control for the separate inputs (XLR / TRS, RCA, TRRS), mic / line gain dial, on / off switch. 48V stop, and a micro / inst mute button.

ikc-L-iRigStream-Pro-Bottom

iRig Stream Pro will allow you to stream / record up to 4 audio sources and just once, giving you many more options than before. For example, you can connect a guitar or bass to the XLR / TRS combo jack, a DJ rig like the XDJ-XZ to the RCA and a pair of headphones with a mic to the TRRS input, and route the output. from your smartphone / tablet / laptop to jam with a backing track. It might be a bit too much, but the ability to be creative is there, and it will be exciting to see how the creators use all of these inputs.

It can be confusing to see two headphone inputs, but one is meant to be used strictly for monitoring your main output, and the other is for use with headphones with mics or TRRS mics, like the iRig Mic Lav.

The loopback feature allows you to route audio output from your primary device (iPhone, iPad, Android, Mac, or PC) to iRig Stream Pro. This option allows you to mix it with any other incoming signal – which is very useful. So think about backing tracks, or doing a podcast with a DJ mix, or even processing the audio through other apps (see video below).

Another cool feature is the ability to record / stream in stereo or multi-channel mode. So the iRig Pro will automatically be in stereo mode, which mixes all the inputs into one stereo output, which most creators will use when streaming. Multichannel mode allows you to route each separate channel to a DAW like Logic, Ableton, etc.

Multichannel mode also allows you to use Loopback + which allows you to route one or both channels 3 and 4 to applications for processing, then route their outputs through the Loopback function and into channels 1+. 2 going to your streaming app.

The iRig Stream Pro comes with three cables to connect to your devices, including USB, USB-C, and lighting cables that are easily interchangeable. A word of advice, find a carrying case for your device and cables, as it is easy to lose them. You also get a set of AA batteries which you can use to power it or use bus power through a Mac / PC if you don’t want to rely on battery power. The other alternative is to get an optional DC power cable to supply power through an outlet, so there are plenty of options.

ikc-L-iRigStream-Pro-3-4DX

IRig Stream Pro Specifications

Commmon

  • Type: 2 inputs / 2 outputs or 4 inputs / 2 outputs
  • Conversion: 24-bit A / D, 24-bit D / A
  • Sampling rate: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
  • To be able to: powered by USB bus. 48V operations with iOS devices require battery or DC IN input. When connected to an external power supply (iRig PSU 3A, not included), iRig Stream Pro charges the connected iOS Lightning device.
  • Measure: 3x LED for the overall streaming signal. Peak indicator for Mic / Inst input.
  • Device connection: mini-DIN
  • Dimensions: 123mm / 4.84 “x 67mm / 2.63” x 40mm / 1.57 “
  • Weight: 146g

Entry line

  • Connector: 2x RCA (unbalanced) Left / Right
  • Nominal input level: -10 dBV
  • Clearance: 10 dB – Level @ max
  • Input impedance: 16.5k Ohms
  • Response frequency: from 20 Hz to 20 kHz (-1.5 dB)

Microphone input

  • Microphone input: balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
  • Microphone input level: from 3.8 mV RMS to 388 mV RMS
  • Microphone input impedance: about 2 kOhms
  • Analog gain range: 40 dB
  • Phantom power: + 48V ± 4V
  • Response frequency:
  • from 20 Hz to 20 kHz (-1 dB) Gain @ min
  • from 20 Hz to 20 kHz (-3 dB) Gain @ max

Recommended articles

Instrument input

  • Instrument input: unbalanced, Hi-Z, Jack TS 1/4 “, Tip: signal / Shielding: ground
  • Instrument input level: from 70 mV RMS to 1.8 V RMS
  • Instrument input impedance: 1M Ohm
  • Analog gain range: 28 dB
  • Response frequency:
  • from 20 Hz to 20 kHz (-1 dB) Gain @ min
  • from 20 Hz to 20 kHz (-3 dB) Gain @ max

Headphones / Phones

  • Connector: 1/8 “TRRS jack (CTIA wiring standard)
  • Supply voltage:> 2.5V
  • Microphone gain: Adjustable with numbered dial
  • Response frequency: 20 Hz – 20 kHz
  • Headphone level control: numbered wheel

Battery life

  • Phantom power enabled with an iOS device: up to 20 hours (alkaline batteries), with mic input connected to a 3.1 mA phantom-powered load

To note: all measurements made with the Stream Level button at 0dB.

Package includes

  • IRig Stream Pro interface
  • Lightning to mini-DIN connection cable with charging functions (60 cm / 23.62 “)
  • USB C-Type to mini-DIN connection cable (60 cm / 23.62 “)
  • USB type A to mini-DIN connection cable (60 cm / 23.62 “)
  • 2 x 1.5 V AA batteries
  • Velcro tape

Screenshot 2021-12-11 at 7.12.54 PM

iRig Stream Solo (MSRP $ 49.99)

The iRig Stream Solo simplifies things a bit and comes at a much more affordable price, just under $ 50. This device targets new streamers, hobbyists, or those on a tight budget and is relatively easy to use. The Solo is designed for iOS and Android mobile devices, which is fine for most casual creators because that’s what they use anyway. You can still connect up to 3 sources for your stream, which is not bad considering the price. You also get battery power and the loopback feature.

What are the important sacrifices? These are the audio quality, the number of inputs and the possibility of using it with a computer. You also need to use the Apple Lighting to TRRS dongle to connect it to an iPhone, which is manageable but not as good as having interchangeable cables.

Screenshot 2021-12-11 at 7.18.13 PM

So who is it suitable for? If you’re a DJ, vlogger, or podcaster, the Solo should do the trick, unless you’re concerned with audio quality and can expand later. The main input is a 2-level RCA line that works great for DJs and multi-channel mixers and keyboards, synths, etc.

The headphone / microphone jack, like the iRig Pro, allows you to listen and talk simultaneously on the other inputs, which is ideal for DJs and podcasters. The level of the main input signal (line + mic) is managed with a dial to make sure everything sounds good.

The Loopback switch allows you to route the audio output from your iOS / Android device to iRig Stream Solo so that you can mix it with the other audio. Again, very similar to the iRig Pro.

Overall for the price, this device is solid and gives a designer on a budget sturdy features.

Pro tip: If you have the extra cash, we recommend going with the pro as it’s much more versatile, offers better sound, and is something you can grow into.

Screenshot 2021-12-11 at 7.14.53 PM

IRig Stream Solo specifications

  • Captive TRRS cable to connect to your device
  • Connect a mixer, DJ setup and more via the RCA inputs
  • Headphone output with integrated microphone input
  • All signals added in mono for streaming
  • Looping mixes incoming signals with audio from your device
  • Direct monitoring via headphone output
  • 1/8 “mono Thru line output for cameras, mixers, etc.
  • Powered by 2 AA batteries
  • Works with all your favorite apps


Source link

Share.

About Author

Comments are closed.